QCAA Engineering External Exam: Format, Marks and Timing (QCE)
The QCAA Engineering external exam is a combination response exam on Unit 4 only, worth 25% of your QCE Engineering result and set and marked by QCAA. Under the 2025 syllabus you get 5 minutes perusal and 120 minutes working time, with the QCAA Engineering formula book, a non-programmable scientific calculator, a protractor and a ruler, and no notes. The 2022 to 2025 papers, set under the 2019 syllabus, had a 10-mark multiple-choice section and two short-response sections (written, then calculation), totalling 77 to 85 marks.
This guide describes Engineering 2025 v1.4 (March 2026). The first external exam set on it is the 2026 sitting. No 2026 paper, marking guide or sample external assessment on the 2025 syllabus was available for this guide, so every past paper and subject report below is from a 2019-syllabus sitting and is labelled by year. The whole course is in the QCAA Engineering study guide (QCE), and the papers themselves are on the QCAA Engineering past papers (QCE) page.
What is the QCAA Engineering external exam?
It's the only one of your four assessments that QCAA sets and marks, and it is common to all schools. The syllabus says the paper "consists of a number of different types of questions relating to Unit 4". Those can ask you to:
- respond with multiple choice, single words, or "sentences or paragraphs (up to 150 words per question)"
- sketch or draw a graph, table or diagram
- "calculate using formulas drawn from across Unit 4 subject matter"
- "interpret unseen stimulus materials"
Unit 4 is Machines and mechanisms, with three topics: machines in society, machines, mechanisms and control and materials.
The paper assesses objectives 1, 2, 3 and 5. The syllabus also fixes the mix of question types, each within plus or minus 2%:
| Question type | Share of marks |
|---|---|
| Simple familiar | 60% |
| Complex familiar | 20% |
| Complex unfamiliar | 20% |
The Engineering IA2 guide explains what the three types mean, since IA2 uses the same mix.
How long is the Engineering exam, and what can you bring?
| Under the 2025 syllabus | |
|---|---|
| Perusal | 5 minutes |
| Working time | 120 minutes |
| Provided | The QCAA Engineering formula book |
| Equipment | Non-programmable scientific calculator, protractor and ruler |
| Notes | Not permitted |
The syllabus does not state a total mark or a section split for the paper. The covers of the 2023 to 2025 papers print 10 minutes perusal, which was the 2019 rule, so don't plan your perusal from an old cover. What is on the formula book, and what it leaves off, is in the QCAA Engineering formula sheet guide. Dates are on the QCE exam timetable.
What changed for the 2026 Engineering exam?
QCAA's July 2026 summary of changes says "Perusal time has changed to 5 minutes". Set against the 2019 syllabus, the external assessment specification changed in these ways:
| 2019 syllabus | 2025 syllabus | |
|---|---|---|
| Perusal | 10 minutes | 5 minutes |
| Length of written answers | 800 to 1000 words in total, items of 100 to 150 words | Up to 150 words per question |
| Stimulus | "seen or unseen" | "unseen" |
| Question mix | The same 60/20/20 mix, given as approximate shares | 60%, 20%, 20%, each plus or minus 2% |
| Complex familiar questions | "typically objectives 3 and 5" | "any of the objectives" |
| Formula resource | A formula sheet | The Engineering formula book, with "additional formulas for gears, pulleys, power and efficiency" |
| Full sentences, balance across objectives | Required in the specification | Not in the specification |
On word length, the summary says the change has "no material effect" on the exam.
What changed in Unit 4 content
QCAA says "Subject matter has been reordered across units", that "Logic gate circuit diagrams and truth tables have been explicitly added to Unit 4", and that "New content includes series and parallel circuits, heat treatments and polycarbonate applications." In detail:
- Electrical circuits are new. Series and parallel circuits (), electrical power and energy, and electrical efficiency. None was in the 2019 Unit 4. None of the 2023 or 2024 papers, or the 2025 written and calculation sections, asked a circuit, or calculation, though motor power-efficiency questions (2023 Q17, 2025 Q20c) did appear.
- Steel classes changed. The 2019 syllabus named mild (0.15 to 0.30% carbon), low, medium, high (0.60 to 1.25%) and ultra-high (1.25 to 2.00%) carbon steel. The 2025 syllabus has low (0.07 to 0.30%), medium and high (0.60 to 2.0%), with no ultra-high class and no "mild". It adds hot and cold working, annealing, normalising, hardening and tempering.
- The named plastics changed. 2019 named polyethylene, polypropylene, ABS, PLA, PVC and nylon. The 2025 Unit 4 names ABS, polycarbonate and polyamide (PA6).
- Machines are more specific. Pulleys are "(fixed and moveable, using one continuous rope)", with MA or VR found from the number of ropes. Belts are flat and V. Gears are spur, worm and rack and pinion, with GR or VR formulas. Version 1.4 added VR of screws as circumference divided by pitch.
- Stress-strain is uncertain. The 2019 Unit 4 named stress-strain; the 2025 Unit 4 materials subject matter does not. It sits in Units 1 and 3, and the syllabus says Unit 4 extends Units 1, 2 and 3, so the documents don't settle whether a stress-strain diagram will appear on the external paper.
These carry over unchanged: the bicycle, car jack and crowbar; the four types of motion; MA, VR, levers, inclined planes and screws; work, power, kinetic and potential energy, and efficiency; the motion equations; friction and the angle of repose; a one-body inclined plane; logic gates and truth tables; the lead-tin diagram and lever rule; and steel microstructures.
How many marks were the past Engineering papers?
Every 2019-syllabus sitting from 2022 to 2025 was one paper in three sections: Section 1 multiple choice (10 marks), Section 2 short response with written answers, and Section 3 short response with calculations. The split between the two short-response sections moved each year.
| Sitting | Section 2, written | Section 3, calculation | Total |
|---|---|---|---|
| 2022 | 7 questions, 41 marks | 5 questions, 34 marks | 85 |
| 2023 | 5 questions, 30 marks | 6 questions, 45 marks | 85 |
| 2024 | 6 questions, 33 marks | 6 questions, 36 marks | 79 |
| 2025 | 6 questions, 34 marks | 6 questions, 33 marks | 77 |
No source gives the 2026 total, question count or layout, so treat these as the shape of the old paper. The 2023 and 2024 multiple-choice questions were printed in a separate book from the response book.
How are the Engineering exam marks awarded?
The exam is marked against the External Assessment Marking Guide, a separate document for each year. In the 2023, 2024 and 2025 guides, short-response marks were awarded one per bullet, and three rules applied to calculations:
- Intermediate working was correct "within a range of two to a maximum of nine decimal places".
- "Final answers must be provided to the nearest whole unit or as otherwise stated in the question".
- A follow-through mark was available if later working showed "the correct conceptual understanding or skill".
On 2025 Q21 and Q22, and 2024 Q15 and Q20, the marking guide accepted two methods. The 2024 report adds a condition: "Alternative response methods can be awarded full marks only when the answer is correct."
Two marking guides (2024 and 2025) show how a long question's marks split:
| Item | Marks | How the marks split |
|---|---|---|
| 2025 Q22, sled on a 15° slope, | 8 | Free-body diagram 1; normal force identified 1 and calculated 1; friction 1; parallel force 1; net force 1; acceleration 1; distance 1 |
| 2025 Q15, access control | 6 | A valid solution 1; expertise in materials science, mechanics and control technology, 1 each; two benefits, 1 each |
| 2024 Q15, forklift logic circuit | 8 | Connections 3; labels for sensors, gear, engine, E, F and G, and output 5 |
| 2025 Q21, logic circuit | 9 | Connections 3; labels 4; column E 1; column X 1 |
On 2025 Q22, six of the eight marks came before the acceleration. A wrong final answer on that question still left most of the marks available to a student who drew and worked each step.
Which question types keep coming up?
Each of these appeared on at least two 2019-syllabus papers. The last column says whether the 2025 syllabus still supports it. Topic-level figures are in the most tested topics section.
| Question type | Where it appeared | Under the 2025 syllabus |
|---|---|---|
| Explain MA and VR (and work) for a named machine, with an annotated sketch, 4 to 5 marks | 2022 Q11 pulley; 2023 Q12 bicycle; 2024 Q11 crowbar | Still in Unit 4 |
| Logic circuit from conditions or a truth table, labelled | 2024 Q15 (8 marks); 2025 Q21 (9 marks); 2023 Q13 (complete a table and explain) | Still in Unit 4, and now named explicitly |
| Engineers' expertise in a community or business problem, 5 to 6 marks | 2023 Q14; 2024 Q16 (flood); 2025 Q15 | Still in Unit 4 |
| Steel selection or microstructure | 2022 Q15; 2023 Q15; 2024 Q13 and Q14; 2025 Q12 | Still in Unit 4, with the new steel classes |
| Justify a polymer from a table or a stress-strain diagram | 2022 Q17; 2024 Q12; 2025 Q14 and Q16 | Changed: different named plastics, and stress-strain is uncertain. Choosing a material from supplied data is the part most likely to transfer |
| Lead-tin diagram: phases and the lever rule | 2024 Q19 and multiple-choice Q1; 2025 Q11 and Q19 | Still in Unit 4 |
| Friction and an incline, multi-step with a force diagram | 2022 Q22; 2023 Q19 and Q20; 2024 Q17, Q20 and Q22; 2025 Q13 and Q22 | Still in Unit 4 |
| MA, VR, efficiency, work, power and energy | 2023 Q16 to Q18 and Q21; 2024 Q18 and Q21; 2025 Q17, Q18 and Q20 | Still in Unit 4, with the changed pulley, gear and screw formulas. Circuit calculations and / are new, and no 2020 to 2024 paper or 2025 written or calculation section tested them |
A repeat shows what QCAA asked under the 2019 syllabus. It doesn't promise a question on the 2026 paper.
What do the multiple-choice results show?
QCAA prints the percentage of students choosing each option in the subject report. Four 2019-syllabus items stand out.
| Item | What it asked | Key | A / B / C / D (%) |
|---|---|---|---|
| 2024 Q10 | Work done when 15 N raises a box 12 m using the pulley shown (3, 90, 180 or 360 J) | D, 360 J | 1.39 / 17.62 / 58.06 / 22.48 |
| 2024 Q2 | Material for highly tempered punches and axles | D, ultra-high carbon steel | 3.63 / 11.49 / 41.89 / 42.55 |
| 2023 Q4 | VR of a belt drive with a 200 mm diameter driver and a 250 mm radius driven pulley (0.40, 0.80, 1.25 or 2.50) | D, 2.50 | 40.17 / 14.19 / 12.03 / 33.35 |
| 2023 Q6 | Which material is best within the proportional limit on a stress-strain diagram | A and B both accepted | 16.36 / 44.81 / 21.77 / 16.74 |
On 2024 Q10, 58.06% chose 180 J, which is the 15 N effort multiplied by the 12 m the box rises. That is our arithmetic; the report gives no reason. The marking guides write work as , the effort force times the distance the effort moves. On 2023 Q4 more students chose 0.40 than the key, and 0.40 is the reciprocal of 2.50. The 2024 Q2 split is between high and ultra-high carbon steel, and ultra-high is gone from the 2025 syllabus.
What does QCAA say costs marks in the Engineering exam?
These themes appear in at least two of the 2022 to 2025 subject reports, all on 2019-syllabus cohorts.
- Read the whole question (2022, 2023, 2024, 2025). Check the marks and the cognitive verb, and answer every piece of information the question asks for. The QCAA cognitive verbs guide (QCE) covers the verbs.
- Round at the end (2023, 2024, 2025). Keep full values through a multi-step calculation and round only the final answer.
- Give the answer in the form asked (2022, 2023). Whole units, a set number of decimal places, and the unit.
- Build logic circuits from the conditions (2022, 2023, 2025). Annotate the inputs and outputs.
- Resolve weight on an incline (2022, 2023). Find the components parallel and perpendicular to the slope.
- MA and VR in complex cases (2022, 2023), including gears (2023). The 2025 syllabus changed the gear and pulley formulas, so practise from the current formula book.
- Link steel microstructure to properties and applications (2022, 2023). Use the 2025 steel classes.
On the other side, the 2024 and 2025 reports praise succinct answers that give only what is asked, and the 2024 report praises responses that refer to the stimulus.
Points raised in one year only
These appeared in a single report, so treat them as one cohort's issues.
- Static and kinetic friction (2025). Distinguish the two, and put arrows on free-body diagrams.
- Lead-tin diagrams (2022). Identify the diagram's features and apply the inverse lever rule.
- Input power from efficiency (2023). Divide by the efficiency as a decimal. The formula sheet guide shows the wrong move the report names.
- Knowns and unknowns (2024). Note them before choosing a method, and avoid short cuts off the method you were taught.
- Use perusal time (2025). Perusal is now 5 minutes, half what that cohort had.
How should you prepare for the QCAA Engineering exam?
Work past questions with only the formula book and a scientific calculator, then mark yourself against that year's External Assessment Marking Guide bullet by bullet. On a long calculation, check which steps earned marks before you look at the final answer. The QCAA Engineering past papers (QCE) page holds the 2020 to 2024 external papers, and the QCAA exam preparation guide (QCE) covers planning across subjects.
Machines, mechanisms and control carried most of the marks on the 2023 and 2024 papers: as mapped by AusGrader onto the 2025 topic names, 62.8% of the 2024 paper's mapped marks (49 of 78) and 77.4% of the 2023 paper's (65 of 84). The most tested topics section has the full breakdown by topic and dot point, from 2019-syllabus papers rather than a 2026 weighting.
Then cover what no 2020 to 2024 paper, and no 2025 written or calculation section, tested: series and parallel circuits, electrical power and energy (, ), heat treatments, polycarbonate, and the redefined steel classes. Work them from the Unit 4 subject matter in the QCAA Engineering syllabus (QCE).
Frequently asked questions
How many marks is the QCAA Engineering external exam out of?
QCAA has not published a total for papers set under the 2025 syllabus, and the syllabus does not state one. The 2019-syllabus papers sat from 2022 to 2025 totalled 85, 85, 79 and 77 marks, each with a 10-mark multiple-choice section.
Are electrical circuits in the QCE Engineering external exam?
Yes, under the 2025 syllabus. Unit 4 now includes series and parallel circuits using V = IR, electrical power and energy, and electrical efficiency. None of the 2023 or 2024 papers, or the written and calculation sections of the 2025 paper, asked a circuit calculation, because the 2019 Unit 4 did not include series or parallel circuits. Practise them from the Unit 4 subject matter instead.
Is there a word limit in the Engineering external exam?
The 2025 syllabus describes written responses as sentences or paragraphs of up to 150 words per question. The 2019 syllabus set 800 to 1000 words in total across the paper. QCAA's July 2026 summary of changes says the word-length change has no material effect on the exam.
When should you round in the Engineering external exam?
At the end. The 2023, 2024 and 2025 External Assessment Marking Guides accepted intermediate values rounded to between two and nine decimal places, and wanted final answers to the nearest whole unit unless the question said otherwise. The 2026 marking guide's wording has not been published.
Can you still use 2019-syllabus Engineering papers to practise?
Mostly. Machines, levers, inclined planes, friction, logic circuits and the lead-tin phase diagram carry over to the 2025 syllabus. Steel classes and the named plastics changed. Mild steel, ultra-high carbon steel and PLA are not in the 2025 syllabus, and polyethylene, polypropylene and PVC are no longer in the 2025 Unit 4 subject matter (they are now in Unit 2 only).
Sources
- Engineering 2025 v1.4 General senior syllabus, QCAA, March 2026, pp. 27-32, 48-51. External assessment specification, conditions and question mix (pp. 48-50), Unit 4 subject matter (pp. 27-32) and the version history.
- Engineering 2019 v1.1 General Senior Syllabus, QCAA, pp. 50-53, 61-63. Superseded version, cited for the conditions and Unit 4 subject matter the 2022 to 2025 papers were set under.
- Key senior subject changes: for external assessment in 2026, QCAA, July 2026, p. 12. The Engineering changes for the 2026 external assessment.
- Engineering subject report, 2025 cohort, QCAA, January 2026, pp. 27-40. Paper structure, multiple-choice response percentages and advice to students.
- Engineering subject report, 2024 cohort, QCAA, January 2025, pp. 48-59. Paper structure, multiple-choice response percentages, alternative methods and advice to students.
- Engineering subject report, 2023 cohort, QCAA, pp. 36-46. Paper structure, multiple-choice response percentages and advice to students.
- Engineering subject report, 2022 cohort, QCAA, pp. 37-46. Paper structure and advice to students.
- External assessment papers and marking guides, 2020 to 2025, QCAA. The Engineering 2023, 2024 and 2025 question books and External Assessment Marking Guides: cover conditions, question stems, keys, rounding rules and mark allocations.
- AusGrader question bank, QCE Engineering, AusGrader. Marked external assessment papers for 2020 to 2024, and the share of mapped marks by Unit 4 topic.
Syllabus and assessment material referenced in this guide is © State of Queensland (Queensland Curriculum and Assessment Authority), licensed under CC BY 4.0. See our QCAA licensing notice. AusGrader is an independent study tool and is not affiliated with, endorsed by, or operated by the QCAA.
Keep reading
QCAA Engineering Formula Sheet: What Is and Is Not on It (QCE)
Every formula on the QCAA Engineering 2025 formula and data book, who supplies it in IA2 and the external exam, and what it leaves off.
QCAA Engineering IA2 Examination: How to Get Top Marks (QCE)
How QCAA Engineering IA2 is marked out of 25: the percentage cut-offs, the 60/20/20 question mix, Unit 3 content and what QCAA reports show (QCE).
Practise what you just read
Work through real QCAA Engineering questions and get your written answers marked against the official criteria, instantly.