QCE Engineering

QCAA Engineering IA2 Examination: How to Get Top Marks (QCE)

QCAA Engineering IA2 is a school-set examination on Unit 3, Civil structures, worth 25% of your QCE Engineering result. It runs for 120 minutes plus 5 minutes perusal, and your percentage on the paper is converted to a mark out of 25 through a table of cut-offs. Getting 25 takes more than 96%, and about 40% of a paper's marks sit in complex familiar and complex unfamiliar questions.

This guide describes Engineering 2025 v1.4 (March 2026), and it is one assessment in QCAA Engineering (QCE). The v1.4 change was to Unit 4 Topic 2 only. Implementation started in 2025, which by our reading makes 2026 the first Year 12 cohort on these rules. The marking rules below are current, but the commentary is older: the 2023, 2024 and 2025 reports all describe 2019-syllabus cohorts, and no report yet covers a marked 2025-syllabus IA2. Report material is labelled by year for that reason. You'll also see different names for this task. The syllabus calls it Examination, combination response. The 2023 and 2024 reports say "Examination - short response", and the 2025 report says "Examination (25%)".

What is the QCAA Engineering IA2?

Weighting25%
Result out of25
ContentUnit 3, Civil structures
Set byYour school
Perusal5 minutes
Working time120 minutes
ConditionsIndividual and supervised. No notes
ProvidedThe QCAA Engineering formula book, from your teacher
EquipmentA non-programmable scientific calculator, a protractor and a ruler
Objectives1, 2, 3 and 5

No question count or mark total is published for the paper. Your school sets them.

The syllabus says the paper includes questions that may ask you to:

  • "respond using multiple choice, single words or sentences"
  • "sketch or draw graphs, tables and diagrams"
  • "calculate using concepts and principles from Unit 3 subject matter"
  • "respond to seen or unseen stimulus materials"

It also includes "instructions to write in full sentences where required", so follow them when you see them.

Unseen stimulus "must not be copied from information or texts that students have previously been exposed to or have used directly in class". Long or data-heavy stimulus is shared with you before the exam.

Four objectives are assessed. Objective 1 starts "Recognise and describe" and objective 2 starts "Symbolise and explain". Objective 3 is "Analyse structural problems and information in relation to structures", and objective 5 is "Synthesise information and ideas to propose possible structural solutions". Objectives 4, 6, 7 and 8 are not listed for IA2.

What do simple familiar and complex unfamiliar mean?

The syllabus fixes the mix of marks on the paper, with an allowance of plus or minus 2%.

Question typeMarksWhat it meansTypical objectives
Simple familiar60%"relationships and interactions are obvious and have few elements", and the procedure is clear or the context "has been a focus of prior learning""Typically these questions focus on Objectives 1, 3, 5"
Complex familiar20%"a number of elements", and the procedure is still clear"can focus on any of the objectives"
Complex unfamiliar20%The same elements, but "the required procedure is not clear from the way the question is posed", in "a context in which students have had limited prior experience""Typically ... Objectives 3, 5"

So the difference between the two complex types is whether the question tells you the procedure. In a complex unfamiliar question you have to work out the method yourself.

Don't expect the sample's questions to come back. The 2025 report tells schools to "include complex unfamiliar items that are sufficiently different to the complex unfamiliar items in the QCAA sample instrument to ensure that students have had limited prior experience". The 2023 and 2024 reports make the same point.

What content is on the Engineering IA2?

Only Unit 3. The 2025 report says: "The IA2 instrument must only assess students' knowledge of Unit 3 subject matter." The 2024 report asks for items "across all three topics of Unit 3". Here's what the current syllabus lists in each.

Topic 1, Civil structures in society.

  • Common construction and processing materials, "including timber, rock, earth, brick, concrete and steel".
  • Corrosion, including dry, wet and stress corrosion, and protection by "(galvanising, sacrificial anode, coatings)".
  • Life cycle effects of one of "timber, concrete, composite materials, glass, bricks or plastics".

Topic 2, Civil structures and forces.

  • "Calculate to solve beam reactions at different types of supports (pin and roller) for vertical, horizontal and angled forces."
  • Truss reactions at supports, and the "method of joints and method of sections (graphical and analytical methods)".
  • "construction of shear force and bending moment diagrams for vertical point loads only (at the end or the middle)."
  • "Comprehend factor of safety."

Topic 3, Civil engineering materials.

  • Contrasting toughness, hardness, brittleness, ductility, and tensile and compressive strength across glass, bricks, wood vs. timber, laminates, polymers, concrete and steel.
  • "Compare and contrast" stress-strain diagrams for soft and hard timber and low-carbon steel.
  • "Contrast tension, compression, transverse and shear tests."
  • Calculating stress, strain, Young's modulus, factor of safety and UTS.

Force components, moments and those material calculations are printed in the Statics and Materials boxes of the formula book. The QCAA Engineering formula sheet guide reproduces them and shows what the sheet leaves out.

How is Engineering IA2 marked?

The instrument-specific marking guide (ISMG) for IA2 is printed in the syllabus. It's separate from the External Assessment Marking Guide, which belongs to the external exam. There is one criterion, Engineering knowledge and problem-solving, covering objectives 1, 2, 3 and 5, for 25 marks.

Each mark has a percentage cut-off, and every cut-off is a strict inequality.

MarkCut-offMarkCut-off
25> 96%12> 50%
24> 93%11> 46%
23> 89%10> 42%
22> 86%9> 37%
21> 82%8> 33%
20> 78%7> 28%
19> 75%6> 24%
18> 71%5> 19%
17> 68%4> 14%
16> 64%3> 10%
15> 60%2> 5%
14> 57%1> 0%
13> 53%0Matches no descriptor above

That example shows a paper total of 76. It isn't a required total, because your school sets its own.

What does each mark range need?

The ISMG also describes the student response at each mark, and the top range reads: "across the full range of simple familiar, complex familiar and complex unfamiliar situations". That range, 25-24, asks for:

  • "accurate and discriminating recognition and discerning description of structural problems, knowledge, concepts and principles"
  • "adept symbolisation and discerning explanation of ideas and solutions"
  • "insightful and accurate analysis of problems and information"
  • "coherent and logical synthesis of information and ideas to propose possible solutions"

Lower down, the opening clause changes, and it shows where the complex questions drop out.

MarksThe clause in the ISMG
25-24"across the full range of simple familiar, complex familiar and complex unfamiliar situations"
23-22"in a comprehensive range of simple familiar, complex familiar and complex unfamiliar situations"
21-20"in a comprehensive range of simple familiar situations, and in complex familiar and complex unfamiliar situations"
19-18"in a range of simple familiar situations, and in complex familiar and complex unfamiliar situations"
17-16"in a range of simple familiar situations and in complex familiar situations"
15-14"... and in some complex familiar situations"
13-12"in simple familiar situations"
11-10"in simple familiar situations"
9-8"in some simple familiar situations"
7-6"in a limited range of simple familiar situations"

Complex unfamiliar situations appear down to 19-18 and not below it. For the wording below 7-6, read the ISMG.

Here's what the cut-offs do to a paper built exactly to the nominal 60/20/20 mix. This is our arithmetic, not a QCAA statement, and a real paper can sit 2% either side:

  • Every simple familiar mark and nothing else is 60%. The cut-off is strict, so 60% isn't "> 60%". It lands at "> 57%", which is 14.
  • Add every complex familiar mark and you have 80%, which is "> 78%", or 20.
  • 25 needs "> 96%".

QCAA Engineering IA2 exemplars from the subject reports

The reports reproduce handwritten responses with the question stems blanked. All three were written under the 2019 syllabus, and each shows one question, so read them as examples of layout. They aren't rules for every question.

What the subject reports say about marking

Beyond a graph of the mark distribution, reports say little about how students did on IA2. They describe how schools' papers and marking were checked, which tells you how your own paper should be built.

Alignment. Before a school uses an assessment, QCAA checks it and approves it, which is called endorsement. Alignment was the leading reason IA2 instruments were not endorsed in all three reports, with counts of 70 in 2023 (from 102 submissions), 80 in 2024 and 86 in 2025. The 2024 report wants marks "balanced according to the syllabus' specified percentage of marks and degree of difficulty", and the 2025 report wants items to "align with the question specifications in relation to the degree of difficulty". Those counts describe schools' papers, not students.

Jargon. All three reports flag terms from outside the syllabus: "culverts" and "Mars" (2023), "king posts" (2024) and "homogenous" (2025).

Marking schemes name what earns the mark. The 2025 report says evidence in short-paragraph answers "used key terms and ideas that were specifically identified in the marking scheme", and that "in calculation questions, the marking scheme stated where follow-through errors were permitted". The 2024 report says "full marks were awarded for responses to short response written items that addressed each requirement of the question".

Marks follow your school's scheme for that question. The 2025 report gives one truss example: "where the marking scheme for a truss question does not allocate marks to calculating the angle of the truss, marks should not be awarded for this calculation." Other questions may be different.

On length, the current syllabus list above names sentences. The 2024 report, on the older task, mentions short-paragraph items "students can answer" in 100 to 150 words, and items "suitable for the two-hour time limit".

Common mistakes in Engineering IA2

Revising the wrong unit. The paper can only assess Unit 3, so time on other units earns nothing here. The 2024 report says "levers and mechanical advantage are Unit 4 content so should not be assessed in IA2". Watch older material on stress and strain too. The 2023 report's comment on them described the 2019 syllabus, and those calculations are now in Unit 3 Topic 3.

Practising only the sample's complex unfamiliar questions. Your school's are meant to be different from them. Practise working out a method from the information given.

Rounding your percentage. The 2024 report says "rounding up the raw percentage score for the paper to the nearest whole number is avoided", and the 2023 report asks for at least one decimal place. Because the cut-offs are strict, check any self-marked practice paper the same way.

Weak versus strong answers

The reports give no weak excerpts. Each weak entry below is our opposite of a characteristic the reports or the ISMG state, not a real student answer, and the strong entries come from one question each.

WeakStrongBasis
General facts about a materialNames each factor asked for and links the property to its consequence2025 report, timber response
A truss answer that jumps to a member forceA force diagram (it carried a mark on that question), then equations with T or C2025 report, method of sections
Final diagrams onlyReactions, shear each side of the loads, moments, then the diagrams2024 report, shear force and bending moment
Marks from simple familiar questions onlyReaches the complex questions, where the clause in the ISMG changesISMG and the arithmetic above

The weightings for all four assessments are on the subject page, and the QCE Engineering syllabus shows where these Unit 3 topics sit.

Practise and get it marked

Practise this IA on AusGrader: sit a prewritten practice IA where your subject has one, or build your own from real QCAA questions, and get it graded against the marking guide with feedback. You can also upload your IA draft for feedback against the ISMG.

Frequently asked questions

How long is the QCE Engineering IA2 exam?

5 minutes perusal and 120 minutes working time, under supervision. Your teacher provides the QCAA Engineering formula book, and you use a non-programmable scientific calculator, a protractor and a ruler. You can't bring notes.

What percentage do I need for 25 out of 25 in Engineering IA2?

More than 96% on the paper. The cut-offs are strict inequalities, so exactly 96% does not meet that line and sits at the mark below, which is 24 (more than 93%).

Is the Engineering IA2 paper marked out of 25?

The result is. The paper itself can have a different total, because no mark total is published and your school sets the paper. The 2023 report's example is 48.5 out of 76, which is 63.8%. That is above 60% but not above 64%, so the mark is 15.

Why do QCAA subject reports call this task short response?

The reports on the 2023, 2024 and 2025 cohorts describe the 2019 syllabus. The 2023 and 2024 reports call it Examination, short response, and the 2025 report calls it Examination. The current syllabus calls it Examination, combination response.

Can stress and strain calculations be in Engineering IA2?

Under the 2025 syllabus, stress, strain, Young's modulus, factor of safety and UTS are calculations listed in Unit 3 Topic 3, and IA2 assesses Unit 3. Older advice on this comes from the 2019 syllabus, so go by the current subject matter.

Will the complex unfamiliar questions match the QCAA sample?

They shouldn't. The 2025 report tells schools to write complex unfamiliar items that are sufficiently different to those in the QCAA sample instrument, so that students have had limited prior experience of them.

Sources

  • Engineering 2025 v1.4 General senior syllabus, QCAA, March 2026, pp. 23-26, 38-42, 51. Unit 3 subject matter, the IA2 specification and conditions, the instrument-specific marking guide and the version history.
  • Engineering 2025 formula and data book, QCAA, June 2026, p. 1. The Statics and Materials formulas named in this guide.
  • Engineering subject report, 2025 cohort, QCAA, January 2026, pp. 16-20. Commentary on this examination under the 2019 syllabus, including two student responses.
  • Engineering subject report, 2024 cohort, QCAA, January 2025, pp. 24-28. Commentary on this examination under the 2019 syllabus, including one student response.
  • Engineering subject report, 2023 cohort, QCAA, February 2024, pp. 19-23. Commentary on this examination under the 2019 syllabus, including the worked cut-off example.

Syllabus and assessment material referenced in this guide is © State of Queensland (Queensland Curriculum and Assessment Authority), licensed under CC BY 4.0. See our QCAA licensing notice. AusGrader is an independent study tool and is not affiliated with, endorsed by, or operated by the QCAA.

Keep reading

Practise what you just read

Work through real QCAA Engineering questions and get your written answers marked against the official criteria, instantly.